How does a cold storage tank shift cooling demand off-peak?

2026-11-13

A Cold Storage Tank shifts cooling demand off-peak by storing chilled water when electricity demand or prices are lower, then using that stored cooling to serve part of the load during peak hours. In a data centre, this can reduce the chiller capacity needed during a busy electricity period, although pumps and other cooling equipment may still need to run.

The distinction is between cooling demand and electricity demand: the servers still produce heat during the peak period. The tank changes when much of the electricity used to remove that heat is consumed. Whether this lowers operating costs depends on the electricity tariff, the charging schedule and the energy required by the complete system.

From chilled water to shifted electricity use

A chilled-water storage system normally works through two operating phases: charging and discharging. The tank sits within a wider cooling arrangement that includes chillers, pumps, controls and the equipment that transfers heat away from the data centre.

  1. Charge the tank: During the selected off-peak period, chillers produce chilled water. Depending on the system configuration, they may cool the live data centre load at the same time as they charge storage.
  2. Hold the cooling: Insulation limits heat gain while the chilled water remains in the tank. Good internal flow management helps maintain a separation between colder and warmer water, commonly called stratification.
  3. Discharge during peak hours: Chilled water is supplied from storage to the cooling system. Water returning from the load is warmer and enters the appropriate part of the tank. Chillers can reduce output or stop only when the remaining system capacity and operating requirements allow it.
  4. Recharge: After the peak period, the chillers restore the tank’s stored cooling for the next scheduled discharge.

The tank does not generate cold on its own. It holds water that was cooled earlier, so a shift in chiller operation requires enough off-peak time and capacity to recharge it. A tank that finishes the peak period partly discharged may still provide value, but controls must account for its actual state before the next cycle.

A simple way to understand storage capacity

The useful cooling stored in water depends mainly on the volume available and the usable temperature difference between the cold supply and warm return. A larger usable temperature difference allows a given volume of water to carry more cooling. In practice, the entire nominal tank volume is not necessarily available at ideal temperatures throughout discharge.

Consider a facility that wants to reduce chiller operation across a defined peak-price window. The first question is not simply how large the tank should be, but how much cooling must be supplied from it during each hour of that window. That requirement depends on the expected load, the chiller capacity that will remain available and any reserve the operator chooses to retain.

For an initial estimate, the required stored energy can be approximated by multiplying the intended average cooling contribution by the discharge duration. The result then needs adjustment for factors such as mixing, heat gain, operating margins and the temperatures the connected equipment can accept. Detailed sizing also has to account for changes in load over the discharge period rather than relying on an average alone.

What happens to the chillers during the peak?

Storage can support either full or partial shifting. With full shifting, the stored cooling is designed to cover the relevant load for the specified period, allowing the chillers to remain off if the rest of the system permits. With partial shifting, chillers continue running but supply less cooling while the tank covers the difference.

Partial shifting may be appropriate when the peak window is long, the cooling load is high or there is insufficient space for a tank sized to cover the entire load. It can also avoid requiring all of the charging capacity needed for a full-discharge strategy. The trade-off is that some chiller electricity use remains during the peak.

Charging itself must fit the operating schedule. If chillers are already close to capacity while serving the live load overnight, there may be little spare capacity to cool the tank. Extending the charging period, changing the operating strategy or adding capacity may be necessary; the right choice depends on the actual load profile and equipment limits.

Conditions that determine whether shifting works

Temperature and flow

Stored water must reach the cooling equipment at a temperature and flow rate that meet its requirements. Excessive mixing inside the tank can raise the supply temperature sooner than expected, reducing usable storage. Return water that is cooler than anticipated can also reduce the temperature difference used in sizing, leaving less cooling available from the same volume.

Monitor supply and return temperatures alongside flow, rather than judging performance from tank temperature at one point. In a stratified tank, sensors at different heights can help show how the boundary between cold and warm water moves during charging and discharge.

Controls and timing

A time schedule alone may not be enough. Controls need to coordinate tank state, chiller availability, valve positions and pump operation while maintaining the required supply conditions. They should also define what happens if the tank reaches its discharge limit before the peak period ends: the chillers or another approved cooling source must be able to take over without interrupting the load.

Peak and off-peak periods should be checked against the actual electricity agreement. A low energy price at one time does not automatically mean the same schedule minimises the bill, particularly where demand charges or other tariff conditions apply.

Electrical use beyond the chiller

Moving cooling production to another time is not the same as eliminating electricity consumption. Charging and discharging can add pumping energy, and stored water gradually gains heat. Chiller efficiency may also differ between charging and direct cooling conditions. Compare the whole-system electricity use and relevant tariff periods before assuming that a larger shift will produce a saving.

Checking the system before relying on stored cooling

Commissioning should verify both the storage cycle and the transition between operating modes. A useful test plan checks whether the tank reaches its intended charged condition, whether the required discharge flow and supply temperature are maintained, and whether chillers respond correctly when storage is depleted or unavailable. Measurements should include temperatures, flow, valve position and electrical consumption where instrumentation permits.

For controlled load testing, a Liquid-Cooled Dummy Load can simulate an electrical load and transfer heat to a water-cooling circuit. The stated model is rated at 30 kW and offers flow or hydraulic differential-pressure control, remote status monitoring and USB data export. It is a test load, not a storage device; its connection, flow range and temperature limits must be checked against the system being tested.

Finally, assess storage performance under the conditions it is intended to handle, including a representative peak duration and the expected charging window. A successful short discharge does not by itself establish that enough cooling is available for the entire peak or that the tank can be fully recharged before the next one.