Why does pressure drop rise across a heat exchanger?

2026-11-12

A rising pressure drop across a heat exchanger usually means that fluid is meeting more resistance as it passes through the unit, or that the flow rate has increased. Fouling, blocked passages, a partly closed valve and changes in fluid temperature can all produce a similar reading. Before cleaning or dismantling the exchanger, compare the pressure difference at the same flow rate, temperature and operating configuration as an earlier baseline.

Measure the difference between the inlet and outlet pressure on the same fluid circuit. A liquid-to-liquid heat exchanger has two separate circuits, and each has its own pressure drop. Identifying which side is changing narrows the search: debris in a facility water loop, for example, does not establish that the coolant side is obstructed.

Start with the operating conditions

Pressure drop normally rises as flow increases, even when the exchanger is clean. A pump speed change, a control valve opening or a change in the number of active cooling loads can alter flow through the unit. Compare the current flow reading with the clean or previously stable reading before treating a higher differential pressure as evidence of fouling.

Temperature matters as well. Cold liquid is often more viscous, so a coolant circuit starting up at a lower temperature can show a higher pressure drop than it does when warm. The concentration of a glycol mixture also affects viscosity. Compare readings at similar inlet temperatures and with the same fluid mixture; a pressure difference recorded during a cold start is a poor baseline for normal warm operation.

Use the exchanger manufacturer’s pressure-drop data where available, matching the fluid and flow conditions to the data. A reading above a design point does not by itself prove a fault if actual flow or fluid properties differ from those assumed in the design.

When deposits or debris restrict the passages

Fouling reduces the open area available for flow and increases resistance. Scale from water chemistry, corrosion products, biological growth and sediment are common sources. In a plate heat exchanger, narrow channels are especially sensitive to debris; in a shell-and-tube unit, tube-side deposits or obstructions on the shell side can produce a similar trend.

A gradual increase in pressure drop at a stable flow rate supports a fouling investigation. A simultaneous loss of heat-transfer performance adds evidence, but it is not conclusive: changes in inlet temperatures or heat load also affect outlet temperatures. Record flow, inlet and outlet temperatures on both circuits, and pressure drop together so that the thermal and hydraulic trends can be interpreted against the same operating conditions.

A sudden increase points toward a different set of possibilities. Debris released after maintenance, a collapsed hose lining, a lodged valve component or a rapid change in valve position can restrict flow quickly. A strainer installed upstream may collect material before it reaches the exchanger. Measure pressure on both sides of the strainer separately; otherwise, a dirty strainer included in the measurement can be mistaken for a fouled exchanger.

Confirm what the pressure readings include

Pressure taps located directly at the exchanger connections give a more useful reading for the exchanger itself than taps separated by valves, strainers or long pipe runs. If the available taps include those components, their resistance is part of the indicated differential. A partly closed isolation valve, for example, can raise the measured pressure drop even when the exchanger passages are clean.

Verify that both pressure instruments use the same units and reference. A drifting gauge, blocked sensing line, trapped air in an instrument line or incorrectly located differential-pressure connection can create a misleading trend. Where safe and practical, compare the readings with a calibrated instrument using the same pressure points. Do not loosen a pressurised connection to investigate a suspect reading.

Gauge pressure at the inlet alone is not enough to diagnose exchanger resistance. Inlet pressure can rise because of a pump or valve change while outlet pressure rises with it. The relevant figure is the inlet-to-outlet difference, interpreted alongside actual flow.

Flow restriction and loss of cooling do not always match

A high pressure drop can reduce flow if the pump cannot maintain its previous flow against the added resistance. Reduced flow can then limit heat removal, particularly during a high cooling load. Yet an exchanger can also lose thermal performance with little change in pressure drop: a thin insulating deposit, air accumulation or an unsuitable temperature difference between circuits may affect heat transfer before a clear hydraulic change appears.

Conversely, a higher pressure drop caused by increased flow does not automatically mean cooling has deteriorated. Compare the heat load and temperatures as well as the pressure readings. On a data centre cooling circuit, distinguish the exchanger’s differential pressure from the pressure available to the connected cooling equipment; a problem in one part of the loop is not necessarily located in the other.

If critical equipment approaches its permitted temperature while the cause is being investigated, follow the site’s emergency operating procedure. In an emergency cooling arrangement, a Liquid Cooling Emergency Device is intended for rapid cooling and heat dissipation. Its use depends on the approved system arrangement and does not identify the source of the pressure rise.

Restore flow without creating a second problem

Once the restricted circuit and component are identified, select the corrective action to match the cause. A blocked strainer needs a different response from deposits inside exchanger channels. If cleaning is required, use a method compatible with the exchanger construction, plate or tube material, seals and deposited material. An unsuitable chemical or excessive cleaning pressure can damage the unit or move loosened debris into another part of the circuit.

Isolate, depressurise and drain the relevant section under the site’s maintenance procedure before opening it. For plate units, follow the manufacturer’s instructions on disassembly, gasket handling and reassembly; some designs are not intended to be opened for mechanical cleaning. Where flushing is permitted, consider where the discharge and dislodged material will go, and protect downstream equipment.

After the circuit is restored, remove air as required, return valves to their intended positions and bring flow back under controlled conditions. Record the pressure drop at a known flow rate and temperature. That reading becomes useful evidence for the next comparison, especially if the trend begins to rise again soon after cleaning, when the underlying source of contamination or unsuitable water chemistry may still be present.