A cold storage tank should be sized for the cooling energy the system must supply when solar-powered chilling is insufficient—not simply for the building’s peak cooling load or the solar array’s capacity. The key decision is how much cooling must remain available, for how long, and at what water temperature.
A preliminary tank volume can be calculated from the required cooling energy and the usable temperature difference between stored cold water and returning warm water. That estimate must then be checked against charging time, chiller capacity, insulation losses, available space, and the reliability of pumps and controls during the intended backup period.
Start with an hourly cooling-load profile for the operating conditions the system is intended to handle. Include the load during occupied hours, overnight operation, and any critical equipment that cannot tolerate an interruption. Distinguish the full design load from the smaller load that could be maintained under an agreed emergency operating mode.
The relevant storage period is the interval when cooling demand exceeds the output available from the chiller. For a solar-powered system, that interval may begin before sunset if photovoltaic generation falls below the power needed to run the cooling plant. It may also extend into the morning until sufficient generation or another power source becomes available.
Where grid power, batteries, or a generator can operate the chiller, the tank may only need to cover the remaining shortfall. Where no backup electricity is available, storage must cover the cooling load for the specified autonomy period—and the system must still have a way to power the circulation pumps and controls. Cold water in a tank cannot provide useful cooling if it cannot be delivered to the load.
Use a defined design scenario rather than an unspecified “cloudy day.” State the expected solar generation, starting tank charge, cooling demand, and availability of backup power. A longer autonomy period can substantially increase tank volume and the chiller capacity required to recharge it.
For each hour of the design period, subtract the cooling that can be produced directly from the cooling demand. Add the positive shortfalls to estimate the energy the tank must discharge. If the tank is recharged during the same period, account for that charging only when the chiller has sufficient electrical power and spare cooling capacity.
For a constant load with no direct cooling contribution, the estimate is simpler:
Required storage energy (kWh thermal) = cooling load (kW) × discharge duration (hours)
For example, a required cooling load of 100 kW over six hours calls for 600 kWh of delivered cooling. This is thermal energy, not the electrical energy consumed by the chiller. The electricity needed to charge the tank depends on the chiller’s efficiency at its actual operating conditions and on auxiliary consumption.
If the load varies, an hourly calculation is more useful than multiplying the peak load by the entire period. However, the peak discharge rate still matters: a tank with enough total energy can fail to maintain the required supply temperature if its connections, heat exchangers, or pumps cannot deliver the necessary cooling rate.
For a water tank using sensible heat storage, a preliminary calculation is:
Tank volume (m³) = storage energy (kWh) ÷ [1.163 × usable temperature difference (°C) × usable storage fraction]
The factor 1.163 represents the approximate thermal capacity of one cubic metre of water per degree Celsius. The usable temperature difference is the difference between the coldest stored water and the warmest tank water that can still deliver acceptable cooling at the load. It is not automatically the difference between the chiller’s supply and return temperature settings.
Suppose the system needs to deliver 600 kWh, the usable water temperature range is 8°C, and an illustrative usable storage fraction of 0.85 is adopted to account for non-ideal operation:
600 ÷ (1.163 × 8 × 0.85) ≈ 76 m³
That is a preliminary nominal water volume, not a finished tank specification. The 0.85 fraction is an example, not a universal design allowance. It should be replaced with an estimate supported by the tank configuration, expected stratification, flow rates, and supplier or engineering calculations. Heat gain from the surroundings must be included separately unless it is already covered by the chosen allowance; do not count the same loss twice.
The calculation assumes liquid water. Glycol mixtures have different thermal properties, and ice or phase-change storage requires a different calculation based on usable phase-change energy and operating conditions.
The allowable tank temperature range depends on the temperature needed at the equipment or air-side cooling coil, the return temperature, and any temperature difference required across heat exchangers. A wider usable temperature range reduces the calculated water volume, but it is only valid if the load can still be cooled at the warm end of discharge.
Lowering the charging temperature can increase stored energy per cubic metre, but it can also reduce chiller efficiency or require different equipment. Conversely, a higher chilled-water temperature may improve chiller performance while limiting the cooling available from each cubic metre. Compare these effects over the full charging and discharging cycle rather than selecting the smallest tank in isolation.
In liquid-cooled equipment applications, include the approach temperature of the cooling distribution unit or other heat exchanger between the tank and the equipment loop. Controls must also prevent supply conditions outside equipment limits, including temperatures that could create condensation where relevant.
Storage capacity is useful only if the system can replenish it before the next discharge period. Calculate the charging energy needed after a design discharge, then test it against the hours when sufficient electrical power and chiller capacity are available.
For illustration, restoring 600 kWh of cooling in five hours requires an average net charging rate of 120 kW, before storage losses. If the chiller must also serve a simultaneous 80 kW load, it needs approximately 200 kW of cooling output during that period, subject to actual operating conditions. The solar array and any electrical backup must be able to supply the corresponding chiller and auxiliary power.
A nameplate chiller rating or peak solar output alone does not establish that this is feasible. Check generation and demand over the charging window, including reduced output under the selected weather scenario. If the tank cannot be fully recharged, the next day begins with less usable storage; repeated partial-charge days should therefore be included when they are part of the required operating scenario.
Thermal stratification helps preserve a cold layer for delivery, but inlet design, excessive flow, and mixing can reduce the volume available at the required temperature. Ask for a tank design and control strategy that address charging and discharging flow rates, sensor locations, and the point at which the system declares the tank depleted.
Insulation should be assessed against ambient temperature, tank surface area, storage duration, and condensation risk. Heat ingress matters most when water remains stored for long periods or the tank is installed in a hot space. Pipework, valves, and exposed fittings also add heat gain and should not be ignored in the overall cooling balance.
Confirm the hydraulic arrangement early: tank connection sizes, pump duty, pressure losses, expansion provisions, and any heat exchanger separating the tank from the distribution circuit. Site access, tank dimensions, structural loading, maintenance clearance, and whether the vessel can be installed in one piece can affect both the feasible volume and the project schedule.
Emergency cooling equipment may provide a separate response to a critical-load event, but it should not be assumed to replace the tank’s specified autonomy. A Liquid Cooling Emergency Device is intended for rapid cooling in emergency situations; its capacity, duration, power requirements, and integration with the existing cooling circuit must be established before crediting it in the storage calculation.
Before issuing the tank specification, document the design load profile, required autonomy, usable temperature range, assumed losses, charging schedule, and backup power arrangement. Review the resulting volume together with the required discharge rate and recharge capacity: all three must work under the same design scenario.
Leave A Message
If you are interested in our products and want to know more details, please leave a message here, we will reply you as soon as we can.